How To Make A Booster Bag

DISCLAIMER: This article is intended for educational purposes merely. The authors exercise non condone shoplifting, and any information contained in this blog post should non exist used to appoint in illegal activities. In fact, we encourage retailers and their agents to keep abreast of such shoplifting techniques, every bit this helps to inform them of how their loss prevention strategies may exist circumvented.

Put simply, a booster purse (sometimes called a 'magic bag') can be used to foil a store'due south EAS (electronic article surveillance) detection system by blocking the RF or AM point which is contained in a security tag or characterization. Substantially, the bag acts as a shield which prevents the tag from beingness detected past the security gate as it is passed. The bag is made of tin or aluminium foil, and this can be layered inside a shopping bag, backpack, or even the lining of a pocket within a slice of clothing.

Unlike opportunistic shoplifters, booster bags are used past professional thieves equally an easier means of concealing multiple items in one visit. It also saves time for the would-be thief, as there is no need to remove security tags or labels inside the shop. Nearly often, the shoplifter would utilise sleight-of-mitt or a store blind spot to driblet items into the bag. A more crude method involves wrapping ready-made layers of foil around an item at the time of lifting, and then sealing the foil with a fold.

What items are needed to make a booster handbag?

In our instance nosotros'll depict how a double-layered booster purse is made. The two layers enable the handbag to appear normal when viewed from either the inside or outside (i.e. unlike the picture shown higher up, it prevents any metal from being seen). In this experiment, you lot'll demand:

• Two new (not old and creased) shopping bags
• A scroll of tin foil
• Adhesive tape (double-sided works best)
• A pair of scissors

How is the booster bag made? [Log in or reigster to go access to the video]

1. Find a big, flat surface and lay out your tools.
2. Fold the first edge of the roll well-nigh 5cm (2") over, cogitating side in.
3. Gyre-out some foil, reflective side up, and place ane bag against the inside edge.
4. The handle of the bag must not be covered by any foil (you'll see why later). Also, the bottom part of the purse may be exposed for now, and this is OK.
5. Unroll some more length, and lay it over the pinnacle side of the pocketbook. The new crease should be as shut as possible to the edge – do not make information technology wider than the bag's width considering your outer purse will need to fit over information technology.
6. Grab the ii corners of the pocketbook that are closest to the roll of foil, then lift the purse upwards, and as more than foil unravels, flip the bag underneath so that the newest layer is on pinnacle.
7. Press down the newly made edge and then that it creases closely with the edge underneath.
8. Repeat this process so that it makes four complete layers (remembering that each flip of the bag covers simply i side – i.east. half a layer).
9. When you have completed 4 layers (this is enough to block any signal from penetrating), tear off the last edge of foil, and employ adhesive tape to seal information technology down.
10. If the lesser part of your bag is withal exposed (i.e. information technology's longer than the width of foil), repeat the process above, but ensure that the bottom of the purse sits above the bottom lining of foil with about 5cm (ii") spare.
11. Next, at the base of your pocketbook, fold the bottom edge of foil upwards, so that backlog length is removed. Tape this bottom edge thoroughly so that information technology creates a dainty seal.
12. Your (rigid) bag now needs to rest within an outer bag to muffle the foil lining. Carefully insert your foil purse so that it sits all the way inside the outer bag, right down to the bottom.
13. Tip: You tin gently unflatten the foil pocketbook edges so that information technology puffs out slightly, making it easier to insert (a puffier looking purse is not undesirable, considering it makes an empty bag look full).
14. The bag must be pushed all the style downwardly, so that the handles of both line up evenly.
15. Fold the top of the outer bag outwards so that the within bag's handle is exposed.
16. Utilize double-sided agglutinative tape near to the top edge and handle areas of the inside handbag (on both sides), so that the outer pocketbook can seal directly on top of information technology. Avoid placing tape on any of the foil.
17. Unfold the outer bag and seal it down onto the tape.

How do you test a booster bag?

1. Place a jail cell phone inside the your booster purse.
2. Selection upwards the bag past the handles, and hold information technology naturally, as you would in a store.
3. Telephone call the cell phone from another line. If it doesn't ring, your bag is secure. If it did, you may demand more layers, or bank check that the top of your bag has been sealed down thoroughly.

Source: https://www.tagremovers.com/how-do-booster-bags-work/

Share this post